| 1 | <?xml version='1.0' encoding='UTF-8'?>
|
|---|
| 2 | <!DOCTYPE topic PUBLIC "-//OASIS//DTD DITA Topic//EN" "topic.dtd">
|
|---|
| 3 | <topic xml:lang="en-us" id="install-linux-manual">
|
|---|
| 4 | <title>Performing a Manual Installation</title>
|
|---|
| 5 |
|
|---|
| 6 | <body>
|
|---|
| 7 | <p>
|
|---|
| 8 | If you cannot use the shell script installer described in
|
|---|
| 9 | <xref href="install-linux-alt-installer.dita#install-linux-alt-installer"/>, you can perform
|
|---|
| 10 | a manual installation. Run the installer as follows:
|
|---|
| 11 | </p>
|
|---|
| 12 | <pre xml:space="preserve">./VirtualBox.run --keep --noexec</pre>
|
|---|
| 13 | <p>
|
|---|
| 14 | This will unpack all the files needed for installation in the
|
|---|
| 15 | directory <codeph>install</codeph> under the current
|
|---|
| 16 | directory. The Oracle VM VirtualBox application files are contained
|
|---|
| 17 | in <filepath>VirtualBox.tar.bz2</filepath> which you can
|
|---|
| 18 | unpack to any directory on your system. For example:
|
|---|
| 19 | </p>
|
|---|
| 20 | <pre xml:space="preserve">sudo mkdir /opt/VirtualBox
|
|---|
| 21 | sudo tar jxf ./install/VirtualBox.tar.bz2 -C /opt/VirtualBox</pre>
|
|---|
| 22 | <p>
|
|---|
| 23 | To run the same example as root, use the following commands:
|
|---|
| 24 | </p>
|
|---|
| 25 | <pre xml:space="preserve">mkdir /opt/VirtualBox
|
|---|
| 26 | tar jxf ./install/VirtualBox.tar.bz2 -C /opt/VirtualBox</pre>
|
|---|
| 27 | <p>
|
|---|
| 28 | The sources for Oracle VM VirtualBox's kernel module are provided in
|
|---|
| 29 | the <filepath>src</filepath> directory. To build the module,
|
|---|
| 30 | change to the directory and use the following command:
|
|---|
| 31 | </p>
|
|---|
| 32 | <pre xml:space="preserve">make</pre>
|
|---|
| 33 | <p>
|
|---|
| 34 | If everything builds correctly, run the following command to
|
|---|
| 35 | install the module to the appropriate module directory:
|
|---|
| 36 | </p>
|
|---|
| 37 | <pre xml:space="preserve">sudo make install</pre>
|
|---|
| 38 | <p>
|
|---|
| 39 | In case you do not have sudo, switch the user account to root
|
|---|
| 40 | and run the following command:
|
|---|
| 41 | </p>
|
|---|
| 42 | <pre xml:space="preserve">make install</pre>
|
|---|
| 43 | <p>
|
|---|
| 44 | The Oracle VM VirtualBox kernel module needs a device node to
|
|---|
| 45 | operate. The above <userinput>make</userinput> command will tell
|
|---|
| 46 | you how to create the device node, depending on your Linux
|
|---|
| 47 | system. The procedure is slightly different for a classical
|
|---|
| 48 | Linux setup with a <filepath>/dev</filepath> directory, a
|
|---|
| 49 | system with the now deprecated <userinput>devfs</userinput> and a
|
|---|
| 50 | modern Linux system with <userinput>udev</userinput>.
|
|---|
| 51 | </p>
|
|---|
| 52 | <p>
|
|---|
| 53 | On certain Linux distributions, you might experience
|
|---|
| 54 | difficulties building the module. You will have to analyze the
|
|---|
| 55 | error messages from the build system to diagnose the cause of
|
|---|
| 56 | the problems. In general, make sure that the correct Linux
|
|---|
| 57 | kernel sources are used for the build process.
|
|---|
| 58 | </p>
|
|---|
| 59 | <p>
|
|---|
| 60 | Note that the <filepath>/dev/vboxdrv</filepath> kernel module
|
|---|
| 61 | device node must be owned by root:root and must be
|
|---|
| 62 | read/writable only for the user.
|
|---|
| 63 | </p>
|
|---|
| 64 | <p>
|
|---|
| 65 | Next, you install the system initialization script for the
|
|---|
| 66 | kernel module and activate the initialization script using the
|
|---|
| 67 | right method for your distribution, as follows:
|
|---|
| 68 | </p>
|
|---|
| 69 | <pre xml:space="preserve">cp /opt/VirtualBox/vboxdrv.sh /sbin/rcvboxdrv</pre>
|
|---|
| 70 | <p>
|
|---|
| 71 | This example assumes you installed Oracle VM VirtualBox to the
|
|---|
| 72 | <filepath>/opt/VirtualBox</filepath> directory.
|
|---|
| 73 | </p>
|
|---|
| 74 | <p>
|
|---|
| 75 | Create a configuration file for Oracle VM VirtualBox, as follows:
|
|---|
| 76 | </p>
|
|---|
| 77 | <pre xml:space="preserve">mkdir /etc/vbox
|
|---|
| 78 | echo INSTALL_DIR=/opt/VirtualBox > /etc/vbox/vbox.cfg</pre>
|
|---|
| 79 | <p>
|
|---|
| 80 | Create the following symbolic links:
|
|---|
| 81 | </p>
|
|---|
| 82 | <pre xml:space="preserve">ln -sf /opt/VirtualBox/VBox.sh /usr/bin/VirtualBox
|
|---|
| 83 | ln -sf /opt/VirtualBox/VBox.sh /usr/bin/VBoxManage
|
|---|
| 84 | ln -sf /opt/VirtualBox/VBox.sh /usr/bin/VBoxHeadless</pre>
|
|---|
| 85 | </body>
|
|---|
| 86 |
|
|---|
| 87 | </topic>
|
|---|
